Launch Campaigns

18/01/2023

Product description and intended use  SE-MONT-BICAPA-40 is a double layer self-adhesive strip of 4 cm width made of EPDM CR-130 RE 42 microcellular of 2.5 mm + 3 mm poliethylene to be attached to metal channels, studs and ceiling profiles. It has excellent soundproofing properties.  It is also a material with good performance against atmospheric agents and with very low thermal conductivity.  It is used in soundproofing systems to disconnect the metal frame and the drywalls.  It is a material which absorbs the resonance between components.    Installation guide  The double layer strip is attached to the metal frame side which will be in contact with the drywall, decreasing the resonance between both components.    Reference  SE-MONT-BICAPA-40: rolls of 20 lineal meters    Main benefits  - Effective for soundproofing. - Ease and of installation. - It avoids v...

[View more]

14/09/2021

Description and uses   The TAV-500/11 designed and produced by SENOR is an antivibration acoustic plug made of a polymer(rubber) and a cold rolled steel DC04 bowl-shaped of 1,6 mm thickness with a zinc-patinated finish.   There are two models: TAV-500/11 A for floor and wall fastening and TAV-500/11 R for ceiling fastening.   Its main purpose is the soundproofing of wall partition and wall lining systems (channels and studs). The TAV-500/11 is used to fix the channels in the perimeter providing elasticity to the system. In order to get the best acoustic results, it is crucial to use it. In this way, the metal frame is isolated totally. The screws do not come into contact with channels, avoiding the vibration transmission between the original building structure and wall partition or wall lining systems.   The acoustic rubber EPDM strip is recommended to get a perfect sealing of both wall partition or wall lini...

[View more]

18/08/2021

  Description and uses The models 3800 y 3801 TD1 + TA, designed and manufactured by SENOR, are wall mounts to build acoustic wall lining systems. They are made of a high quality polymer (rubber) which allows to decrease vibrations and isolate sound frequencies, a galvanized steel DX51D + Z275 MAC bracket and a screw (7 cm) with a nylon wall plug used to hold wall mount to the wall lining system. The 3800 TD1 + TA bracket is 1,5 mm thickness. Its use is to build wall lining system with more than 10 cm air chamber. The 3801 TD1 + TA bracket is 0,8 mm thickness. Its use is to build wall lining system with less than 10 cm air chamber. When fixed to the stud, the rest of the bracket can be folded with your owns hands (see images on the back). Both are used to isolate wall lining system with self-supporting metal structure (channels and studs) from original wall. They are placed in vertical studs. References SE-3800/TD1 + TA: 1,5...

[View more]

09/08/2021

Description and uses   The TRN-70 designed and produced by SENOR is a fastening piece made of 1.5 mm thickness high quality galvanized steel DX51D + Z275 MAC. It has a polypropylene bushing with a special nut (nut + washer). Thanks to the bushing material, thermal break is obtained. The special nut provides security in the event of overtemperature or overload.   Its main application is suspended ceiling installation using metal channels such as T-15, T24 or similars.   References   SE-TRN/704-M4: fastening piece (metric 4) SE-TRN/706-M6: fastening piece (metric 6) This product is available in 20 and 200 units boxes.   Main benefits   - Easy and fast installation.   - It does not conduct electricity.   - It provides thermal break which avoids cold and heat transmission. Minimal loss of space.   - It avoids condensations from temperature changes.   - Nuts are not ne...

[View more]

09/08/2021

Description and uses   The bowl-shaped leveller designed and produced by SENOR is a fastening accessory made of 1.6 mm cold rolled steel DC04 with a zinc-patinated finish. It has two anchor points providing more safety.   Its main purpose is to hang gypsum ceiling systems and/or heavy objects from the ceiling, such as FCU’S or ducts. This piece can be used in any surface: timber, concrete and iron.   References   SE-CN4-2-M4: Bowl-shaped leveller (metric 4) SE-CN6-2-M6: Bowl-shaped leveller (metric 6) This product is available in 100 and 30 units boxes.   Main benefits   - Robustness: 1.6 mm thickness allows more security than the rest of fastening accessories that are usually 1 mm thickness or even less.   - The two anchor points guarantee a stabler support.   - It can be used in any surface: timber, concrete, iron.

[View more]

03/08/2021

Description and uses   The HORQ/DS designed and produced by SENOR is a fastening piece made of high quality galvanized steel DX51D + Z275 MAC with a 1.5 mm thickness. It has a polypropylene bushing with a special nut (nut + washer) inside. It has locking device (DS) which guarantee a stabler fastening.   Its main purpose is to hang gypsum continuous ceilings using 47 and/or 60 mm metal channels.   References   SE-HORQ/47DS-M6: Fastening hanger for 47 mm channels (metric 6) This product is available in 30 and 100 units boxes. SE-HORQ/60DS-M6: Fastening hanger for 60 mm channels (metric 6) This product is available in 24 and 80 units boxes.   Main benefits   - It can be placed easly in the channel.   - The locking device (DS) ensure the piece to the channel.   - The polypropylene bushing:    - allows easy and quick leveling.    - does not conduct electri...

[View more]